A special product from the LITHOFIN-Range for marble, natural and concrete stone (MN). Lithofin MN Power-Clean is free of solvents, low in odour and economical in use. It is a mildly alkaline cleaner, which contains a balanced mixture of cleaning components which guarantee optimal performance.
Properties This special cleaner is nearly odourless and highly economic. Lithofin MN Power-Clean removes grease and oil, all kinds of general and ingrained dirt as well as floor polish residues, old acrylic emulsions, care products, etc.
Technical Data:
Density: approx. 1.0 g/cm³
Appearance: liquid, colourless, clear
Odour: pleasant
pH-Value: approx. 10
Flash Point: n.a.
Solubility in Water: complete
Field of Use
For thoroughly cleaning used or exceptionally dirty natural stone surfaces and for initially cleaning newly laid surfaces. Suitable for use on polished, finely honed and rough marble and other natural stones. Facilitates removing cement residues from polished marble. Suitable for indoor and outdoor use.
Directions for Use
Apply and evenly distribute Lithofin MN Power-Clean diluted up to 1:10 and wipe the surface. In case of stubborn dirt deposits, apply undiluted or diluted up to 1:5 with a brush and distribute. Allow the product to work for 10 to 20 minutes; brush occasionally. Do not allow to dry, add water if necessary. Brush again before wiping up. On large areas, use a squeegee to remove the product. Wash the surface thoroughly with clean water. If the result is not satisfying, repeat the process allowing the product to work longer and brushing more vigorously.
Please Note: avoid splashes on sensitive areas such as metal or wood, painted or varnished surfaces, wall paper, etc. Always test the product in an inconspicuous area prior to use.
Coverage: as supplied: approx. 5 to 10m² depending on dirt diluted: up to 30m²
Advice: for removing wax layers and the like, we recommend Lithofin WAX-OFF.
For cement residues and rust discolorations on granite, gneiss and similar acid resistant stones, use Lithofin MN Builders’ Clean.
Storage
Keep closed, cool and dry. Not above 25°C. Shelf life of up to three years.
Environmental Protection
Surfactants are biologically degradable in accordance with EU-regulations. Free of phosphates. Disposal: diluted product may be added to waste water. Containers are made of environmentally friendly polyethylene (PE). Clean containers can be recycled through collection systems.
Safety
Contents: 5-15% non-ionic surfactant; solubilizer; auxiliary agents; scent geraniol.
Labelling according to EG-Guideline 199/45/EG: Xi, irritant.
Risk and Safety Phrases: irritating to eyes. Keep out of the reach of children. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed, seek medical advice immediately and show container or label.
Advice: As with all cleaners avoid prolonged contact with skin or wear rubber gloves, if you have sensitive skin.
First Aid Procedures: in case of inhalation take in fresh air. In case of contact with skin wash off immediately with soap and water. In case of contact with eyes rinse thoroughly with plenty of water and seek medical advice. Do not induce vomiting. If swallowed by mistake drink plenty of water and seek medical treatment.
Emergency Procedures: in case of spill or other release, take up with absorbent material (e.g. sand, sawdust, general-purpose binder). Ensure adequate ventilation. Product does not burn, fire-extinguishing activities according to surrounding.
Additional Information is listed on the Material Safety Data Sheet.
ADR2003: not a dangerous good.
Packaging
500ml bottle with child-proof cap (10 per box)
1 litre bottle with child-proof cap (12 per box)
5 litre canister (4 per box)
Please Note: statements concerning environmental and safety issues refer to the product as delivered (concentrated).
This information should be considered to be informal and non-binding. The products must be used according to local conditions and materials. Always test the product in an inconspicuous area. (AUS/NZ6.11gps/1.10)
A special product from the LITHOFIN-Range for marble, natural and engineered stone (MN). Lithofin MN Stain-Stop is a ready-to-use, solvent-based impregnator that contains high quality water and oil resistant components.
Properties
Lithofin MN Stain-Stop penetrates into the surface and coats the capillaries with an extremely thin, invisible film. Oil, grease and water are therefore no longer absorbed by the surface, but remain on the surface (12 to 48 hours on polished marble and limestone, up to 60 hours on granite and gneiss). During this time, oil can easily be removed without leaving stains. The effectiveness depends on the amount of product absorbed by the surface. The appearance of the natural stone is not affected. Some stones may become slightly darker in colour. The water absorbency of the stone is greatly reduced; the water permeability is only slightly affected. The product is UV-resistant and does not yellow.
Technical Data:
Density: approx. 0.8 g/cm³
Flash Point: about 32°C
Appearance: liquid, colourless
Odor: slightly aromatic
Reduction of water absorbency: approx. 90 to 95%
Permeability: approx. 80 to 90%
Field of Use
For invisible protection against staining and for facilitating maintenance of all natural stone surfaces, including polished marble. Perfect for use on wall and floor surfaces in the kitchen and bathroom, as well as on table tops, window sills and other sensitive surfaces. Suitable for indoor and outdoor use.
Please Note: marble and limestone will remain sensitive to acid.
Directions for Use
The surface to be treated must be absorbent, clean and completely dry. Suitable application tools: cloth, brush or sponge. Without prior experience or in cases of doubt, try the product in an inconspicuous area prior to use. On large surfaces, work in small sections of 10 to 15m².
Apply Lithofin MN Stain-Stop generously until the surface appears wet. Allow the product to penetrate for approx. 15 minutes. Redistribute the excess product and remove puddles and streaks. On highly absorbent materials or on dry spots more product may have to be added. Remove all remaining product residues within 30 minutes using a dry cloth. On large surfaces use a squeegee to remove excess with a polishing machine and a white pad.
Attention! the liquid product must penetrate into the stone. Do not allow the product to dry on the surface.
Please Note: non-absorbent or damp surfaces cannot be impregnated. Glass, ceramics, and surfaces sensitive to solvents (varnishes, wood, etc.) must be protected against splashes.
Application Temperature: the temperature of the surface should be between 10°C and 25°C. Switch off under floor heating.
Drying Time: after approx. 2 hours surface will be dry and ready to be stepped on carefully. Drying process will be complete after 24 hours, do not cover or use suction lifters during this time. Wipe up any spills immediately. The full effectiveness of the impregnator is reached after 5 days.
Coverage: depends on the absorbency of the stone.
Estimates:
polished surfaces: 12 to 15 m²/L
very dense stones: up to 40 m²/L
rough/honed granite: 5 to 7 m²/L
porous sandstone: 3 to 6 m²/L
Durability
Up to 5 years on outdoor surfaces. Indoors the durability depends on the care products used. Strong de-greasing or layer forming products are unsuitable. Heavily used surfaces such as kitchen counters and vanity tops should be touched up once a year with the solvent-free Lithofin STAINSTOP >W<.
Advice: immediately remove stain causing substances. For regular maintenance of floors we recommend Lithofin MN Wash&Clean, for kitchen counter tops Lithofin MN Easy-Clean.
Storage
Closed, cool and dry up to 3 years. Open containers should be used without delay.
Environmental Protection
Contains solvents, free of chlorinated hydrocarbons. Do not flush down drain.
Disposal: liquid product is classified as special waste. Containers are made of environmentally friendly tin plate. Clean containers can be recycled through collection systems.
Safety
Safe for areas where food is handled – this Lithofin product has been tested according to EU-Ordinance 1935/2004 by an independent institute. The product is considered safe for treating natural and artificial stone surfaces that come into direct contact with food stuffs. Ingredients: siloxane, polymers, auxilliary agents.
Labelling according to EU-Directive 1272/2008(CLP): GHS Symbol 02, 07, 08, Danger
Naphtha (petroleum), hydrotreated heavy. Flammable liquid and vapour. May cause drowsiness or dizziness. May be fatal if swallowed and enters airways. Repeated exposure may cause skin dryness or cracking. Keep out of reach of children. Keep away from heat/sparks/open flames/hot surfaces. No smoking. Use only outdoors or in a well-ventilated area. IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician. Do NOT induce vomiting. Dispose of contents and container in accordance with national/local regulations.
Safety: product poses no health concerns once fully dried (confirmed by independent tests conducted at LGA Nuremberg). Do not apply in rooms where lightly wrapped food is stored. Do not spray.
| ADR2015: labelling for transport | ||
| Unit | Label | Notes on freight papers |
|---|---|---|
| a) b) c) d | LQ | none, due to limited quantities |
Packaging
a) 1 litre bottle with child-proof cap (10 per box)
b) 500ml bottle with childproof cap (10 per box)
c) 250 ml bottle with childproof cap (20 per box)
d) 5 litre canister (2 per box)
This information should be considered to be informal and non-binding. The products must be used according to local conditions and materials. Always test the product in an inconspicuous area. (EN5.17sz/5.17)
A special product from the LITHOFIN-Range for marble, natural and artificial stone (MN).
This mildly alkaline, ready-to-use cleaning product is based on high-quality natural soaps, cleaning and care additives.
Properties
Highly active components dissolve dirt, oil and grease and allow for easy and streak-free cleaning. Special additives ensure that the protective effect of impregnators is not diminished with regular use. The surface will therefore remain protected for a long time. Lithofin MN Easy-Clean leaves a pleasant odour.
Please Note: Lithofin MN Easy-Clean maintains and supports the protective effect of Lithofin MN Stain-Stop.
Technical Data:
Density: ca. 1.0 g/cm³
pH-Value: ca. 8
Appearance: liquid, colourless, clear
Odour: fresh
Solubility in water: good, complete
Field of Use
For regular, every-day cleaning of all small natural stone and quartz surfaces such as kitchen work tops, table tops and in sanitary areas. Specially formulated for use on marble and limestone. Also suitable for ceramics, glass and plastic surfaces.
Directions for Use
Spray Lithofin MN Easy-Clean on the entire surface. Allow the product to work briefly, then wipe the surface with a cloth. Surface may have to be buffed with a dry cloth. Please Note: do not spray on hot surfaces.
Coverage: up to 20m² per bottle.
For more stubborn dirt we recommend Lithofin MN Power-Clean.
Storage
Cool and closed. Not above 25°C; can be stored for up to 3 years.
Recommendation
Natural stone floors should be cleaned regularly with Lithofin MN Easy-Care.
Environmental Protection
Surfactants are biologically degradable according to WRMG. Does not contain phosphates. Bottle is made from environmentally friendly polyethylane and can be recycled. Empty containers which are clean or have dried out may be recycled through collection systems. Please see label for details.
Safety
No health concerns according to LGA Nuremberg. Suitable for surfaces on which food is handled. Does not contain poisonous or dangerous substances. As with all cleaners, avoid prolonged contact with sensitive skin or wear rubber gloves. Keep out of reach of children.
Contents: < 5% anionic surfactants, auxiliary agents.
Label according to EU-Directive 1999/45/EG: none.
Risk and Safety Phrases: none.
First Aid Procedures: In case of contact with eyes rinse thoroughly with plenty of water and seek medical advice. In case of ingestion, do not induce vomitting. If swallowed by mistake drink plenty of water and seek medical treatment.
Emergency Procedures: in case of spill or other release, take up with absorbent material (e.g. sand, sawdust, general-purpose binder). Product does not burn, fire-extinguishing activities according to surrounding.
ADR2003/GGVSE:
not a dangerous good.
Packaging
500ml-bottle with Sprayer (10 per box)
1 litre refill-bottle (10 per box)
This information should be considered to be informal and non-binding. The products must be used according to local conditions and materials. Always test the product in an inconspicuous area. (AUS/NZ7.11gps/12.10)
